LittleBits

The motorMate works with the DC motor. This makes it easy to attach wheels, paper, cardboard, and lots of other materials to the DC motor.

Twist this dimmer back and forth to control your circuit. As you twist the knob clockwise, more signal goes to the Bits that follow, brightening lights, speeding up motors, or raising the volume on buzzers.

You know what a button is! It’s a classic: big, round, and springy. Push to turn your creation on, and release to turn it off. Snap a buzzer in place after your button to sound out signals in morse code!

Use the latch to turn any momentary input, like a button or a trigger Bit, into an on-off switch, like a toggle!

The OR Bit is a logic gate with 2 inputs. If input 1 OR input 2 is receiving an ON signal, then it sends an ON signal from its output.

The NAND Bit is a logic gate with 2 inputs. Think of it as "not and." The NAND Bit will always send an ON signal unless both input 1 and input 2 are receiving an ON signal. It’s the exact opposite of the AND Bit.

The NOR Bit is a logic gate with 2 inputs. It sends an ON signal only when neither input is receiving an ON signal. In other words, it’s the exact opposite of the OR Bit. The NOR Bit is good for inventions in which you want the output to be ON, unless 1 or both of its inputs are triggered.

The bright LED (or "Light-Emitting Diode") is a small Bit that puts out a big light. Just like our other LED Bits, it's a great way to shed some light on your creations. Choose the bright LED when you want a LOT of bright white light.

Think of the threshold as a toll booth. When the signal passing through a circuit reaches it, the threshold decides whether or not it can continue. Use it to make any sensor Bit (like a temperature sensor) into a trigger Bit!

The long LED is a flexible lighting option. We call it the "long" LED because the light is connected to the board by a cable, which lets you put the light in some interesting places. One of our favorite tricks is to place the LED in the middle of a foam ball to make it glow!

The XOR Bit is a logic gate with 2 inputs. Think of it as "exclusive or," meaning that it sends an ON signal when it’s receiving an ON signal exclusively from 1 input or the other, but not both.

The branch Bit gives you more options for connecting your Bits: it lets you connect the output of a single Bit to as many as 3 others, oriented in different directions. Use it when you want to trigger light, sound and motion at the same time.

The timeout Bit is a settable timer. Try it after a button and follow it with a light. Press and release the button to start the countdown.

Use this Bit to control your circuits with sound! The sound trigger listens to the noise level in your room, and sends an ON signal when it gets over a certain level. Try it with a Bit that lights up to create a circuit that responds to the snap of your fingers.

Vibration Motorin avulla voit laittaa minkä tahansa esineen värisemään. Tämä Bit sisältää myös vibeSnapin jolla voit yhdistää erilaisia esineitä, kuten paperia, moottoriin.

The random Bit creates unpredictable voltages and trigger signals to create complex sound sequences. It can either produce white noise, or it can control oscillators to make them play random pitches.

The split lets you connect a single Bit to 2 others. If you place an input before the split, it will control the 2 outputs at once, like a single light sensor controlling 2 motors (to spin car wheels!). The flexible wires on the split also allow you to place your Bits farther apart and position them how you like.

The temperatures sensor responds to the temperature surrounding its probe. The higher the temperature it senses, the more signal it sends out.

With this Bit, you can control your circuits with motion. The motion trigger is similar to the sensor on an automatic door: when someone is moving nearby, it sends an ON signal to the following Bits. It's very sensitive, so don't move a muscle unless you want to be detected! Try it with some LEDs to create a security light.

The USB I/O module allows you send and receive digital audio and control voltages to and from a computer. When using in conjunction with a DAW, you can record your Synth Kit directly into a computer without the need of an external audio interface. You can also send audio from a computer into the littleBits system to manipulate it, for example with the filter and delay modules.

The sequencer allows you to connect up to 8 outputs and control them in sequential patterns. Sequences that would take as long as 4 days to program without littleBits will only take you seconds!

The littleBits At-Home Learning Starter Kit provides an easy-to-follow, flexible, and powerful solution for reinforcing STEAM learning at home.This kit is ideal for educators to send home for individualized learning and can be easily facilitated and guided by parents. Our goal is to give you the tools and support you need to empower learners in any environment to create, experiment, and become critical problem solvers through play-based learning and project-based lessons.

The littleBits STEAM+ Kit contains 24 Bits, a newly designed durable storage containers and printed teacher support materials and 40+ hours of standards-aligned lessons to engage the entire class. Integrate programming with the FUSE app to level up and create digital circuits.